This module implements support for the Veris H8035 and H8036 Energy
Meters.
The H8036 is similar to the H8035, but provides much more data.
The Enercept H8035/H8036 is an innovative three-phase networked
(Modbus RTU) power transducer that combines electronics and high
accuracy industrial grade CTs in a single package. The need for
external electrical enclosures is eliminated, greatly reducing
installation time and cost. Color-coordination between voltage leads
and CTs makes phase matching easy. Additionally, these transducers
automatically detect and compensate for phase reversal, eliminating
the concern of CT load orientation. Up to 63 Transducers can be
daisy-chained on a single RS-485 network.
This module was developed using libmodbus 3.1.2, and the H8035. The
H8036 has not been tested. libmodbus 3.1.2 must be present for this
module to build.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Abhishek Malik <abhishek.malik@intel.com>
The Bosch BMI160 is a 3-axis Accelerometer and Gyroscope.
Additionally it supports an external Magnetometer, accessed through
the BMI160's register interface. This driver was developed with a
BMI160 "Shuttle" board, which included a BMM150 Magnetometer.
The device is driven by either 1.8v or 3.3vdc. This driver
incorporates the Bosch BMI160 driver code at
https://github.com/BoschSensortec/BMI160_driver .
While not all of the functionality of this device is supported
initially, the inclusion of the Bosch driver in the source code
makes it possible to support whatever features are required that
the driver bosch driver itself can support.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Abhishek Malik <abhishek.malik@intel.com>
The Veris TEX00 temperature sensor family is made up of a series of
RTD thermistors in wall mount packaging.
This driver was developed using the TED00, which utilizes a 10K Ohm
Type 2 thermistor. However, this driver can support the other 12
variants of the TE series as well by providing the correct sensor type
to the class constructor. These other sensor types have not been
tested. Only the TED00 hardware was tested with this driver.
This sensor must be connected as part of a voltage divider, with the
balancing resistor ideally matched to the sensor's 25C detection
range. For the TED00 (10kt2), a 10K Ohm (1% tolerance) resistor was
used in a circuit like the following:
GND o----|TED00(10k2)|----o----|balanceResistor(10K)|----o VCC (+5vdc)
|
|
|----o A0 (analog input to MCU)
A 3.3vdc voltage can be used as well if desired.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Abhishek Malik <abhishek.malik@intel.com>
The driver adds support for the Veris TEAMS Temperature Transmitter.
It provides it's output via a 4-20ma current loop. The supported
temperature range is 10C to 35C.
This sensor was developed with a Cooking Hacks (Libelium)
4-channel 4-20ma Arduino interface shield. For this interface,
the receiver resistance (rResistor) was specified as 165.0
ohms.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Abhishek Malik <abhishek.malik@intel.com>
The driver was developed using the Veris CWLSHTA CO2 Gas sensor. The
'T' variant supports a temperature sensor, and the 'H' variant
supports a humidity sensor.
All 3 signals are provided by the device as analog 0-5Vdc, 0-10Vdc, or
4-20ma loop current outputs. For devices supporting temperature, the
valid temperature range is 10C to 50C. The humidity ranges from 0% to
100% (non-condensing). The CO2 sensor ranges from 0 to 2000 ppm.
This driver was developed using the 5Vdc outputs and the 4-20ma
outputs. For voltage outputs, your MCU must be configured for 5V
operation. In addition, you must configure the sensor (via it's
configuration switches) to output 0-5VDC only. Using any other analog
reference voltage will require the appropriate external circuitry
(such as a voltage divider) in order to interface safely with your
MCU.
In addition, the sensor can be configured for 4-20ma usage, by
specifying the correct receiver resistance (in ohms) in the
constructor. This sensor was tested with a Cooking Hacks (Libelium)
4-channel 4-20ma Arduino interface shield. For this interface, the
receiver resistance was specified as 165.0 ohms.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Abhishek Malik <abhishek.malik@intel.com>
This driver provides support for the ILI9341 LCD driver via SPI (e.g.
Adafruit 2.8" TFT LCD).
It was implemented and tested on the Edison.
Signed-off-by: Shawn Hymel
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
The driver implements support for the Omega RH-USB Humidity Probe with
Temperature sensor. It connects via an integrated USB cable, and
appears as a serial port.
It does not currently work with Edison (as of this date) due to
missing ftdi_sio and usbserial kernel support.
It was implemented and tested on the Galileo 2.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This module implements support for the Veris HWXPHTX Hardware Protocol
Humidity and Temperature Sensor family. It uses MODBUS over an RS485
interface.
This module was developed using libmodbus 3.1.2, and the Veris HWXPHTX.
This sensor supports humidity, and optionally, temperature, slider
switch, and override switch reporting. The HWXPHTX used to develop
this driver did not include the optional slider or override switches,
however support for them is provided.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This driver was developed using the Veris HD2NVSTA1 humidity
transmitter. The 'T' variant supports a temperature transmitter as
well. Both signals are provided by the device as analog 0-5Vdc or
0-10Vdc outputs.
The A1 variant supports a temperature range of -40C-50C, while the A2
variant supports a range of 0C-50C. Humidity ranges for all devices
in this device family range from 0% to 100% (non-condensing).
Temperature measurement can be disabled by passing -1 as the
temperature analog pin to the constructor.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This module implements support for the Comet System T3311 Temperature
and Humidity transmitter. It uses MODBUS over an RS232 serial port.
You must have libmodbus v3.1.2 (or greater) installed to compile and
use this driver.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
Initial commit of ADS1x15 adc converter. Support for both ADS1015 12 bit
and ADS1115 16 bit adc.
--signoff
Signed-off-by: Marc Graham <marc@m2ag.net>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This is a USB device from Numato Labs that is accessed via a UART. It
provides 16 GPIO's, 7 of which can be configured as analog inputs.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
If MODULE_LIST is set, cmake will only create examples that can be built
with avaialble modules. There has been significant change to cmake file.
Comments show you how to add new examples.
Signed-off-by: Henry Bruce <henry.bruce@intel.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This module was developed using the OpenZWave library (v1.3):
http://www.openzwave.com/
It was developed using a collection of devices (switches and a
multi-sensor) connected via an Aeon Z-Stick Gen5 USB dongle.
It can be used to query (and, where appropriate, set) Values on Nodes
connected to the ZWave network.
Checks are made in src/ozw/CMakeLists.txt to ensure that the
libopenzwave library is installed (via pkg-config). If not present,
then neither the module, nor the example will be built.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This driver was developed using an SX1276 based shield on the Galileo
G2. It requires 3.3v of operation. It does not work with Edison, due
to SPI issues.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
mcp9808: Initial commit for MCP9808 precision temperature sensor.
Add support for MCP9808 precision temp sensor. Implements all features
except for TCrit and TUpper and TLower locking. Functionality includes
alert, interrupt, resolution and hysteresis control.
Signed-off-by: Marc Graham <marc@m2ag.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
The driver implements support for the DFRobot pH sensors. It was
tested with both the standard and Pro versions, calibrated with
standard buffer solutions at pH 4.01 and pH 7.0.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Abhishek Malik <abhishek.malik@intel.com>
This driver was developed based on the DFRobot Triple Axis
accelerometer BMA220 (Tiny):
http://www.dfrobot.com/index.php?route=product/product&product_id=1085
This device can only run at 3.3v DC. Do not connect to 5v.
Added a private function definition for the installISR function. Done because C++
wasn't able to find the function definition for the java bindings.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Abhishek Malik <abhishek.malik@intel.com>
This driver was tested with the DFRobot URM37 Ultrasonic Ranger, V4.
Both UART and analog access modes are supported.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Abhishek Malik <abhishek.malik@intel.com>
This is a basic serial module that allows access to various XBee
devices via a UART port. It was tested with the XBee S6B WiFi Module
and the XBee S1 802.14.4 module.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Abhishek Malik <abhishek.malik@intel.com>
grovemd: add support for 'mode1' stepping and add stepper examples
The current grovemd driver supported 'mode2' stepping, where the
driver simply passed various stepper commands to the board for it to
carry out on it's own.
This doesn't work very well (or at all if you have old/buggy firmware)
so add a new 'mode1' stepper capability. This mode lets the driver
manually control the stepping operation without requiring special
firmware.
This is now the default and recommended mode to use for stepper motors
on this device. It is also more flexible in terms of the maximum
number of steps you can do (mode2 was limited to 254 steps max).
This was tested using a bipolar NEMA-17 stepper motor with an
external 12v power supply.
Note: 'Mode1' and 'Mode2' are the Seeed Studio terms for these different
stepping modes.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
Jon Trulson