This module was developed and tested on the Grove NFC Tag. It is an
8KB EEPROM accessable (with various protection capabilites) via I2C
and NFC capable devices.
The code was based on the Seeed Studio example code with some help
from the datasheet.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This module was developed on the Grove Serial Camera. It connects to
the UART and runs at 115200 baud. It was developed based on the Seeed
Studio Arduino sketch, as there appears to be no protocol
documentation available.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
cmake: make sphinx use a python-staging folder instead of site-packages
This means that you no longer need to install UPM in oder to be able to use
`make pydoc`. The target pydoc now depends on target doc which with SWIG will
cause python modules to be built, making parralel builds work as expected. We
wipe the python-staging directory on each make pydoc as it's a custom_target
and will rerun at every time anyways, copy is cheap and in case a module gets
deleted it avoids the doc still getting built
Signed-off-by: Brendan Le Foll <brendan.le.foll@intel.com>
There were a few issues with this driver, corrected in this update.
1) i2c transactions were not working - I replaced the i2c
implementation with the MRAA i2c class implementation.
2) status check was inverted - fixed.
3) fixed up #defines in header file to avoid naming collisions (ADDR,
etc).
4) Added capability to supply bus and i2c address to ctor, setting
defaults of 0, and TH02_ADDR respectively.
NOTE: For proper operation on Edison using the arduino breakout
board, the voltage needs to be set to 3.3V rather than 5v. On G2, 5v
works fine.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This driver implements support for the Sparkfun Single Lead Heart Rate
Monitor, based on the AD8232 chip.
It simply outputs ADC data that needs to be sent somewhere for
plotting. The Sparkfun page has some suggestions.
Alternatively, if you have an oscilliscope that supports a 'Roll'
mode, you can get an EKG-like display by measuring the OUT pin.
https://www.sparkfun.com/products/12650
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
The driver implements support for the Grove 3-Axis Digital
Accelerometer(±400g), using the h3lis331dl chip.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This module implements support for the Grove BLE (Bluetooth Low
Energy) device. It is implemented as a UART device accepting an "AT"
command set.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
The module supports the LV-MaxSonar EZ1, EZ2, EZ3 and EZ4 ultrasonic
range finders. It was developed and tested on the EZ3 variant.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This was tested with the Grove FM Receiver. Unfortunately, there is
no documentation on how to control the device using the D1 and D2 pins
that Seeed provides. There is a switch on the device that can control
all of the elements, power, volume, and seek +/-.
The supplied example can turn the device on, and do a seek, but not
much else.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
Mihai Tudor Panu